Material comparison
NBR, EPDM, FKM and Silicone Comparison
Four elastomers account for a large share of O-rings and rubber seals: nitrile (NBR), EPDM, fluoroelastomer (FKM) and silicone (VMQ). They behave very differently in oils, water, steam, chemicals and temperature. This guide summarises their general character so you can shortlist a material, then confirm it.
- NBR
- EPDM
- FKM
- Silicone
At a glance
| Material | Generally good with | Generally poor with | Typical uses |
|---|---|---|---|
| NBR (nitrile) | Mineral oils, greases, many fuels, water | Ozone and weathering, some solvents, strong polar fluids | Hydraulic and lubrication seals, general industrial |
| EPDM | Water, steam in suitable grades, many dilute chemicals, brake fluids of glycol type | Mineral oils, fuels, most hydrocarbons | Water systems, heating, outdoor use |
| FKM (fluoroelastomer) | Oils, fuels, many acids and hydrocarbons, higher temperatures | Some ketones, esters, hot water and steam in some grades, amines | Chemical, fuel and higher-temperature seals |
| Silicone (VMQ) | Wide temperature range, ozone and weathering | Low tear and abrasion resistance, many oils and fuels, dynamic duty | Static seals, some food and medical grades |
These are general tendencies. Individual compounds within each family vary, and the manufacturer's data decides. Always confirm against the manufacturer's data for your application.
NBR in more detail
NBR is the common choice for oil-based hydraulic and lubricating systems because of its oil resistance and economy. The acrylonitrile content changes the balance between oil resistance and low-temperature flexibility. It is not a good choice where ozone, sunlight or strong chemicals are present.
EPDM in more detail
EPDM resists water, many alkalis and weathering. It must not be used with mineral oil or petrol-based products, which swell it quickly. Peroxide-cured grades are often preferred for hot water or steam, but the exact grade must be confirmed.
FKM in more detail
FKM is chosen where oils, fuels and heat combine, and it offers good chemical resistance in many acids and hydrocarbons. It costs more than NBR and some grades are unsuitable for certain chemicals, hot water or steam. Low-temperature flexibility is limited in standard grades.
Silicone in more detail
Silicone retains flexibility over a wide temperature range and resists ozone and sunlight. Its mechanical strength is lower, so it is generally used for static sealing rather than reciprocating or abrasive service. Food- and medical-oriented compounds exist, but suitability depends on the specific grade, and such duty requires technical review and the correct certification documents.
How to choose
- Identify the medium, including cleaning fluids and additives.
- Identify the temperature range, including peaks.
- Decide whether the seal is static or dynamic.
- Check a chemical compatibility chart from a reliable manufacturer and, for the final decision, the compound data sheet.
- Send us the details for review if there is any doubt.
Related ranges: metric O-rings, imperial O-rings, O-ring cords and rubber gaskets and elastomer products.
Limitations
- This is a general comparison, not a compatibility certificate.
- Mixed media, additives and cleaning chemicals can change the result.
- Temperature and pressure together affect life more than either alone.
- Colour does not identify the material.
- Other options, such as HNBR, FFKM, PTFE and polyurethane, may be better for some duties. See the PTFE and graphite guide.
Options & specifications
| Compared | NBR, EPDM, FKM, silicone |
|---|---|
| Decide by | Medium, temperature, static or dynamic duty |
Options, materials and turnaround are confirmed on your written quote.
Frequently asked questions
Which material is best for hydraulic oil?
NBR and FKM are commonly used with mineral hydraulic oils, while EPDM is generally not suitable. Fluid type and temperature decide, so confirm first.
Can I use EPDM with fuel?
Generally no. Fuels and oils swell EPDM.
Is FKM always better than NBR?
No. It resists heat and chemicals better in many cases, but costs more and is not right for every medium.
Is silicone suitable for dynamic seals?
It is usually limited to static use because of its lower strength.
Explore
Metric O-ringsMetric O-rings are described by inside diameter and cross-section in millimetres, for example 20 x 3. They are…View
Imperial O-ringsImperial O-rings are sized in inches, most commonly to the AS568 standard used on American-built equipment, and to…View
Rubber Gaskets and Elastomer ProductsRubber gaskets and elastomer parts cover a broad range: flat gaskets cut from sheet, strip and cord, moulded…View
O-ring CordsO-ring cord is round-section elastomer supplied in lengths or coils, used to make O-rings that are not available…View
How to Measure an O-ringAn O-ring is defined by two dimensions and a material. Get the inside diameter and cross-section right, note…View
PTFE and Graphite Sealing GuidePTFE and flexible graphite are two of the most widely used non-elastomer sealing materials. Both resist a wide…View
How to Measure a Hydraulic SealHydraulic seals are normally specified by groove dimensions, because the seal must fit a particular housing. This guide…View
Gasket Material Selection GuideNo single gasket material suits every flange. Choosing well means matching the material to the medium, temperature, pressure,…View
Not sure of the material? Send us the medium and temperature.
Send your brief, quantities and deadline. We reply with a clear written quote and confirm the turnaround before anything goes to production.
