Bedfordview, Johannesburg+27 79 057 6815+27 78 336 3011

Custom gaskets

Cut and Custom Gaskets

Many gaskets are not available off the shelf: obsolete equipment, imported machines, non-standard flanges or special shapes. Cut and custom gaskets are made from sheet to match a drawing, a sample or a measured flange, using the material suited to the duty. Globseals can quote custom gaskets from your information, and capability for each job is confirmed when you enquire.

  • From drawing, sample or measurements
  • Fibre, PTFE, graphite, rubber and more
  • Single pieces and repeat runs
  • Material advice with the quote
Cut and Custom Gaskets

Overview

A custom gasket starts with two decisions: the shape and the material. The shape comes from the flange or cover, which can be traced, measured, drawn or supplied as a CAD file. The material comes from the fluid, temperature, pressure and bolt load, as described on the Gasket Sheets and Materials page.

Common examples include pump casing gaskets, heat exchanger plate gaskets, cover and inspection-hatch gaskets, gearbox and engine gaskets, valve bonnet gaskets, manway gaskets and large vessel joints. Standard flange shapes, such as round full-face and ring types, are covered under Ring and Full-face Gaskets, while reinforced types are under Spiral Wound Gaskets. For higher volume or specialist production, see our Custom Gasket Manufacturing service, and for conversion of sheet, Gasket Cutting and Material Conversion.

Ways custom gaskets are made

Hand-cut gaskets from a template or flange

For one-offs and repairs. The flange is traced or the old gasket is used as a pattern, then cut with knives, punches and hole cutters. Suitable for soft materials and simple shapes.

Die-cut or punched gaskets

A steel rule or punch tool cuts repeat quantities quickly and consistently. Suited to higher volumes of the same shape, with tooling cost to consider.

CNC knife or router cutting

A computer-driven cutter follows a CAD file, with no dedicated tooling. Good for prototypes, small and medium batches and complex outlines.

Water-jet or laser cutting

Used for harder or thicker materials and some metals, where knife cutting is unsuitable. Material suitability and edge quality vary, and some materials (such as rubber or PTFE) may be unsuited to heat cutting.

Metal-reinforced and layered gaskets

Gaskets with a metal core, tang, insert or laminated layers for higher pressure or blow-out resistance.

Gaskets with sealing beads or coatings

Rubber or graphite facings on metal carriers, for engine and machine parts. These may need technical review.

Materials for custom gaskets

These notes are typical and general. Material choice depends on the duty and must be confirmed against the manufacturer's data.

  • Compressed non-asbestos fibre: general-purpose cut gasket for water, oils and many chemicals.
  • PTFE (virgin, filled, expanded): chemical resistance and cleanliness, with different forms for creep resistance and conformability.
  • Flexible graphite, reinforced: high-temperature and chemical duty, often with a metal insert.
  • Rubber (NBR, EPDM, neoprene, FKM, silicone): soft gaskets for covers, lids and low-pressure flanges.
  • Cork and cork-rubber: engine and gearbox joints on thin or uneven flanges.
  • Mica, ceramic fibre and similar: heat-resistant joints in exhausts, boilers and furnaces.
  • Regulated duties: oxygen, hydrogen, food-contact, pharmaceutical and potable-water use require technical review and the correct certification documents.

How to prepare a custom gasket order

  1. Decide how to supply the shape. Options are a drawing, a CAD file, the old gasket, a rubbing or tracing, or key dimensions.
  2. Measure carefully. For round gaskets give the inside diameter, outside diameter, bolt hole size, number of holes and the pitch circle diameter. See understanding gasket dimensions and flange details.
  3. State the duty. Medium, temperature, pressure and cyclic conditions decide the material.
  4. Choose thickness. Thinner is better when the flange is flat. Thicker suits rough or warped faces.
  5. Specify quantity and repeat needs. One-off and repeat orders may use different cutting methods.
  6. Request a quote. Include photos and any compliance requirements.

Information to send us

  • Drawing, CAD file, sample gasket or accurate tracing
  • Inside diameter, outside diameter, bolt holes and pitch circle diameter, for round gaskets
  • Flange standard and rating, if known
  • Material and thickness, or the medium, temperature and pressure
  • Equipment make and model, and the location of the joint
  • Quantity, and whether repeat orders are expected
  • Photos of the flange, the old gasket and the cover

Genuine and compatible replacements

A genuine gasket is made or supplied by the equipment manufacturer, often in a branded material and sometimes with a part number. A custom or compatible gasket is cut to the same shape from a suitable sheet. This works well for most flange gaskets when the material and thickness are right, but moulded, bonded or coated gaskets from the original maker may have features that cannot be copied by cutting. Where the original gasket is a complex part, ask for technical review.

You can enquire about genuine or compatible gaskets for equipment from manufacturers such as Klinger, Flexitallic, Vulcan, Freudenberg/Simrit, Corteco and Trelleborg.

How to buy

Custom gaskets are normally quoted, since shape, material and quantity differ.

  • Buy online: where a product is listed in the online shop with a confirmed price, you can order directly. Products are being added to the shop progressively, so not every item will be listed yet.
  • Request a quote: for custom, bulk, unpriced or repeat-order requirements, send us a quote request with your details.
  • Technical review: if you cannot identify the part, or the application is demanding, use Find My Seal or upload a drawing and our team will review it with you.

You can also call head office in Johannesburg on 011 079 6033, or WhatsApp 079 508 0989, or email info@globseals.com.

Options & specifications

Information sourcesDrawing, CAD file, sample, tracing or measurements
Cutting methodsHand-cut, die-cut, CNC knife, water-jet or laser, depending on material
Common materialsCompressed fibre, PTFE, graphite, rubber, cork, mica
Typical itemsPump, valve, cover, heat exchanger, manway and engine gaskets
QuantityOne-off repairs to repeat runs, confirmed per enquiry
CapabilityConfirmed when you enquire

Options, materials and turnaround are confirmed on your written quote.

How ordering works

  1. 1

    Gather the pattern

    Collect the old gasket, drawing or flange measurements.

  2. 2

    Define the duty

    State medium, temperature and pressure.

  3. 3

    Agree material and thickness

    Confirm the sheet with our team.

  4. 4

    Quote and supply

    Receive a quote based on your details.

Frequently asked questions

Can you make a gasket from my old one?

Usually yes, if the old gasket is intact enough to trace or measure. Send it or a clear photo with a ruler, along with the flange details and duty. Capability is confirmed when you enquire.

Do I need a drawing?

Not always. A sample, a tracing or accurate measurements can be enough. A drawing or CAD file makes quoting and cutting more accurate.

What if I do not know which material to use?

Tell us the medium, temperature, pressure and the equipment, and we will recommend a material, or arrange a technical review if the duty is demanding.

Can you supply large or multi-piece gaskets?

Large gaskets can be made in sections or with joints in some materials. The method depends on the material and duty, so ask for a technical review.

Can you make repeat batches?

Repeat and bulk requirements are handled by quote. See custom gasket manufacturing and bulk and contract supply.

Request a quote for Cut and Custom Gaskets

Lead times are confirmed with your quote.
Print details
Clothing details
Branding positions (optional)
Sign details

Add a photo of the site or vehicle in the upload box below.

Poster details
Box details
Design or website details
Part details (if known)
Up to 5 files, 25 MB each. PDF, AI, EPS, SVG, PNG, JPG, TIFF, PSD, CDR or ZIP. Files are stored privately.

We use your details only to reply to this request. See our privacy policy.

Related services

Send your drawing, sample or measurements and we will quote your custom gasket.

Send your brief, quantities and deadline. We reply with a clear written quote and confirm the turnaround before anything goes to production.